 |
 |
|
|
|
 |
Shown at left of Long Pin, for comparison.
SmartTrack Short Rear Mount Housing is suitable for kayaks with a vertical, flat section on the stern of the kayak using a bracket. Teflon coated 6061-T6 extruded alloy is extremely rugged and corrosion proof.
• Mounts on the vertical surface of the stern
• Pin measures 2"
See PDF for installation and drawings |
| Part# ST3916 | Download Product Manual (PDF) |
 |
Shown at left of Long Pin, for comparison.
SmartTrack Short Pin Housing is suitable for kayaks with a rudder pivot hole located on a flat or stepped down area on the rear deck. There is often a larger hole that can accept a nylon bushing for the short pin. Teflon coated 6061-T6 extruded alloy is extremely rugged and corrosion proof.
See PDF for installation and drawings
|
| Part# ST3917 | Download Product Manual (PDF) |
 |
SmartTrack Long Pin Housing is suitable for kayaks with an extension or a vertical hole all the way through the rear of the kayak. Teflon coated 6061-T6 extruded alloy is extremely rugged and corrosion proof.
• Mounts on the vertical surface of the stern
• Pin measures 3 5/8"
See PDF for installation and drawings
|
| Part# ST3915 | Download Product Manual (PDF) |
 |
Shown at left. The SmartTrack Foil rudder blade is revolutionary in the field of rudders. It is extremely compact and highly efficient. Using foil design induces 25% less drag and 32% more turning efficiency than an ordinary flat aluminum blade.
See PDF for performance graphs |
| Part# ST3930 | Download Product Manual (PDF) |
|
Shown at right. The SmartTrack Foil rudder blade is revolutionary in the field of rudders. It is extremely compact and highly efficient. Using foil design induces 25% less drag and 32% more turning efficiency than an ordinary flat aluminum blade.
See PDF for performance graphs |
| Part# ST3931 | Download Product Manual (PDF) |
 |
SmartTrack Vertical Adjustment Kit allows lowered installation of the Toe Pilot Controls for better fit or comfort. It also makes it possible to use the existing holes in your kayak to mount your new SmartTrack system if the existing hole have non-standard spacing.
See PDF for installation instructions |
| Part# ST3948 | Download Product Manual (PDF) |
 |
Ergonomically designed, these foot braces employ super tough aluminum rails for increased rigidity and durability.
The two part Toe Pilots foot braces are fixed to provide solid bracing while the movable toe piece allows rudder operation. Easy adjustment from the cockpit.
See PDF for installation and drawings |
| Part# ST3911 | Download Product Manual (PDF) |
 |
Use the toe half of our pedals to set your course, then use the Trim Tab to lock it in. Designed to fit conveniently in front of the paddler, the Trim Tab offers improved accuracy when setting your course.
See PDF for installation instructions |
| Part# ST3825 | Download Product Manual (PDF) |
 |
Rock solid, ergonomically designed foot braces. These braces have rails made from tough, rigid aluminum. Easily adjusted from inside the cockpit.
Mounting holes are set at the standard 14.5" on center.
See PDF for installation instructions and drawings |
| Part# ST3910 | Download Product Manual (PDF) |
 |
For custom fitting kayak cockpits. Dimensions are in 12 increments i.e. 12X12, 12X24 etc. Available in 1/2, 1, 2, and 4 inch thicknesses.
Be aware that dimension over 12X24 can be expensive to ship. |
| |
|
 |
We offer full rolls of black deckline and reflective deckline in 4mm and 5mm.
4mm is approximately 3/16" and 5mm is approximately 1/4"
5mm or 1/4" is the most common dimension used.
This is high quality line that does not fade in the sun.
Rolls are 50M |
| Part# DL-04R | |
|
We offer full rolls of black deckline and reflective deckline in 4mm and 5mm.
4mm is approximately 3/16" and 5mm is approximately 1/4"
5mm or 1/4" is the most common dimension used.
This is high quality line that does not fade in the sun.
Rolls are 50M |
| Part# DL03R | |
|
We offer full rolls of black deckline and reflective deckline in 4mm and 5mm. Our reflective deckline employs a highly visible 3M tracer that offers outstanding night time visibility.
4mm is approximately 3/16" and 5mm is approximately 1/4"
5mm or 1/4" is the most common dimension used.
This is high quality line that does not fade in the sun.
Rolls are 50M |
| Part# DL04RR | |
|
We offer full rolls of black deckline and reflective deckline in 4mm and 5mm. Our reflective deckline employs a highly visible 3M tracer that offers outstanding night time visibility.
4mm is approximately 3/16" and 5mm is approximately 1/4"
5mm or 1/4" is the most common dimension used.
This is high quality line that does not fade in the sun.
Rolls are 50M |
| Part# DL03RR | |
 |
We offer high quality, color fast, shock cord in 5mm, 4mm and 2.5mm diameters sizes.
5mm is approximately 1/4"
4mm is approximately 3/16"
2.5mm is approximately 1/8"
Rolls are 500' |
| Part# SC04R | |
|
We offer high quality, color fast, shock cord in 5mm, 4mm and 2.5mm diameters sizes.
5mm is approximately 1/4"
4mm is approximately 3/16"
2.5mm is approximately 1/8"
Rolls are 500' |
| Part # SC03R | |
|
We offer high quality, color fast, shock cord in 5mm, 4mm and 2.5mm diameters sizes.
5mm is approximately 1/4"
4mm is approximately 3/16"
2.5mm is approximately 1/8"
Rolls are 500' |
| Part# SC02R | |
 |
These spools are 7 strand, 7 wire 1/16" stainless steel rudder cable.
One spool is 250' |
| Part #CBL-R-01 | |
 |
We offer a broad selection of Fasteners - Deck Fittings - Deck Line - Rudder Cables & Fittings - Shock Cord - Shock Cord Fittings - Webbing Hardware
This is an overview of some of our hardware and fittings; see below for detailed component images! |
| Call ! | |
 |
Snap hook for 1" webbing.
Base swivels. |
| Part# WH-SSH04 | |
 |
These are load spreading rivets with a silicone seal to prevent leaking. Neoprene gasket prevents leakage into boat.
Ideal for adding pad-eyes and hardware to sit-on-top and plastic kayaks.
Dimensions - 3/16X1 |
| Part# RIVET-LSH | |
 |
Replacement snap buttons for the ferrel on most two-piece paddles. |
| Part# SNAPB | |
 |
High quality drip rings that fit snug on most past shafts. |
| Part# PDL-DR | |
 |
Suitable for 1" webbing. Attached to kayak using rivet or machine screw. |
| Part# WH-BG04 | |
 |
We offer a 12’ pre-fabricated rudder cable.
7 wire, 7 strand stainless steel
1/16”
Aircraft eyelet swaged on.
Sold individually |
| Part# CBL-PFR | |
 |
Use in conjunction with our pre-fabricated rudder cables and cable crimp sleeves for attaching cable to rudder housing/tiller arm. |
| Part #THM-01 | |
 |
Used in conjunction with our thimble and pre-fabricated rudder cables for rudder repairs and installations. |
| Part # CCS-01 | |
 |
Use to attach a rudder cable to the rudder tiller bar. Use with 1/4-20 Philip Truss machine screw. Create loop in rudder cable using our thimble and cable crimp sleeves. |
| Part # N-RA | |
 |
This is a 1/4-20x1" Philips truss machine screw needed for most rudder cable attachments. Use in conjunction with 1/4-20 Nyloc nut. Use our pre-fabricated cables, cable crimp sleeves and thimbles for complete rudder cable repair and installation. |
| Part # B-PTRUSS 1/4X20/1 | |
 |
We have all the major sizes for installing just about any configuration of accessories and deck fittings.
From left to right:
10-32 x 1 1/4" Pan Head
10-32 x 1" Pan Head
10-32 x 3/4" Pan Head
10-32 x 5/8" Pan Head
10-32 x 5/8" Oval Head*
*This is the most common size; used for nylon pad-eyes.
All stainless steel for the best corrosion resistance. |
| Part # See Price List | |
 |
Stainless steel Nyloc nut suitable for our 10-32 screws. |
| Part #N-1032 | |
 |
Available in 3/4" or 1". Stainless steel. |
| Part # W-10 X 1Fender or W-10 X .75Fender | |
 |
Also known as a strap-eye this is the standard deck hardware for rigging and accessories. Attach with a 10-32 Philips oval machine screw and a Nyloc nut or use our rivets |
| Part # PE-N | |
 |
Popular on many British style kayaks. Suitable for center fastener and two lines. |
| Part# PE-R | |
 |
This deck fitting works on flat surfaces and requires a 10-32 machine screw for installation. Four holes around the perimeter and a single hole in the center for attachment. |
| Part # PE-F | |
 |
Black, gated shock cord hook. Suitable for 1/4 or 3/16" rigging.
Black acetal plastic |
| Part # SC-H | |
 |
Industry standard size. Requires drilling a 3/8" hole. Nut has a brass 10-32 insert. Assembly includes a 10-32x1" SS Philips truss screw for a low profile installation |
| Part #WN | |
 |
These carry toggles are comfortable and easy to retro-fit to other kayaks. |
| |
|
 |
The perfect fitting for routing rudder control cables or other small deck rigging along the deck of the kayak. See larger image for size comparison with a standard pad-eye. |
| Part # ST20-414 | |
|
|
|
Paddlers Supply - Seattle, WA
Tel: 206-935-4121 Fax: 206-935-4245 |
| VisualWebz.com |
